This topic has been archived. It cannot be replied.
-
枫下家园 / 家用电器 / 割草机修理请教诚心请教：割草机固定刀片的螺丝断了，有没有办法更换啊？或者什么地方可以修理？
-southernman(南獒);
2021-6-5
{76}
(#13764636@0)
+1
-
Call the manufacture for a replacement
-troyd(Troy);
2021-6-5
(#13764708@0)
-
我正好也断了,换了一条上去跑了半圈又断了,就不是换螺丝的事了1条螺丝税后近10元,连个响都没听到.肯尼迪路向北过废气后第1个红绿灯右手边有1家专门店可买到螺丝,带上你的割草机型号去配就可以
-xiaozuiba(xiaozuiba);
2021-6-5
{120}
(#13764734@0)
+1
-
关键是怎么取出来？
-southernman(南獒);
2021-6-5
(#13764836@0)
-
网上有些具有智慧结晶好帖子本人都会收集下帖号。看看这个怎么样，帖号是(#13706204@0)，不会发链接，哪位知道怎么发链接
-cocnut(tz);
2021-6-5
(#13765027@0)
+1
-
Did you see the line at the bottom of that page? "To share, click to copy page address.". Also you can bookmark the topic through the Rolia 藏宝箱
-sailor(Ocean & Mountain);
2021-6-5
(#13765049@0)
-
先钻个孔，然后用 screw extractor
-canadagoose(秋雁🇨🇦);
2021-6-5
(#13765040@0)
-
断口多数是个不平整的斜口，想在断口上钻个孔往往会滑到边沿，难。有什么好办法能在斜断口中心钻孔？
-cocnut(tz);
2021-6-5
(#13765128@0)
-
用 center punch 打个小凹陷
-canadagoose(秋雁🇨🇦);
2021-6-5
(#13765183@0)
+1
-
这方法很好，但可能技术不行还是斜面太斜打不住还是往边上滑。还有别的方法解决这个问题吗？谢谢
-cocnut(tz);
2021-6-5
(#13765514@0)
-
用 dremel 把斜面磨平
-canadagoose(秋雁🇨🇦);
2021-6-6
(#13765627@0)
-
两次都相同的斜位断点,有1CM高露在上面
-xiaozuiba(xiaozuiba);
2021-6-5
(#13765114@0)
-
你确定你拧的方向是对的吗？The lawnmower blades itself is not threaded,but most nuts that held the blade in place are reverse threaded. The reverse thread helps to secure the blade on the drive shaft such that the rotation of the blade does not loosen the nut.
-prbw100(tulock);
2021-6-5
{189}
(#13765137@0)
-
螺丝的方向不对能能拧进去吗?
-xiaozuiba(xiaozuiba);
2021-6-6
(#13765657@0)
-
能否麻烦你告知这个商店是在Kennedy/HY7附近吗？
-southernman(南獒);
2021-6-6
(#13766279@0)
-
Kennedy北向过FINCH后第1个红绿灯边右手处,门口有大机器展示
-xiaozuiba(xiaozuiba);
2021-6-6
(#13766296@0)
-
非常感谢
-southernman(南獒);
2021-6-6
(#13766359@0)
-
你确定你拧的方向是对的？The lawnmower blades itself is not threaded,but most nuts that held the blade in place are reverse threaded. The reverse thread helps to secure the blade on the drive shaft such that the rotation of the blade does not loosen the nut.
-prbw100(tulock);
2021-6-5
{189}
(#13765134@0)
+2